Module wires not properly connected to controller terminals. Wires from the Solar Sync module to the controller have been severed. Is the Solar Sync module installed on a controller that has the SOLAR SYNC dial position? If so, remove the module. … ERR …

Program your Hunter controller as specified in the Owner’s Manual. When setting station run times, enter the time that would normally be programmed during the peak summer watering season. The Solar Sync is designed to adjust all run times daily based upon …

After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …

After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …

Using the screws provided, mount the Solar Sync sensor on any surface where it will be exposed to unobstructed sun and rainfall, but not in the path of sprinkler spray. The sensor needs to be oriented upright and the swivel bracket can be moved for …

The Rain-Clik TM portion of the Solar Sync Sensor will keep the irrigation from starting or continuing during rainfall. No adjustment or calibration is required for the Rain-Clik TM sensor. The Rain-Clik TM uses patented Quick Response TM technology that …

If the Rain Sensor or Freeze Sensor is preventing system operation,  SENSOR OFF  will be displayed on the controller’s display. Simply move the Bypass switch on the controller to  BYPASS  and the Solar Sync’s Rain and Freeze Sensor will be bypassed. This …

  Maintaining the sensor The Solar Sync sensor is designed for outdoor use, but must be kept clean to function correctly. Wiping the clear dome covering the solar radiation sensor every 6 months is recommended. Do not use harsh chemicals or abrasives on …

Solar Sync Troubleshooting Guide …

If a Solar Sync sensor has been installed on the Pro-C controller then the seasonal adjust value used by the controller will be calculated from the weather data supplied by the Solar Sync sensor. If it is decided that the Solar Sync sensor will no longer …

After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …

Seasonal Adjustment is used to make global run time changes without re-programming the entire controller. To use the Seasonal Adjustment feature: NOTE: The controller should always be initially programmed in the 100% position. … To view the adjusted run …

After Solar Sync has been installed and programmed, we recommend allowing the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the sensor, …

For controllers with the Solar Sync Module installed, the Region and Water Adjustment is made on the Solar Sync Module. … For accurate measurements, the Solar Sync module needs to be programmed for the typical ET (average July ET) for your region. Press …

Connecting to the ICC The Hunter ICC controllers require the installation of the Solar Sync module as well as the Sensor. Installing the Solar Sync Module Turn off AC power to the controller before connecting the Solar Sync module to the controller. …

The X-Core Controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. Installing the Wireless Solar Sync Sensor Simply mount the Wireless Receiver on the controller cabinet using an available …

The ACC Controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. Installing the Wireless Solar Sync Sensor Simply mount the Wireless Receiver using the supplied brackets to mount the Wireless …

The Wireless Solar Sync Receiver and Sensor are already paired with the same frequency for an easy installation. When installed, the wireless Receiver will automatically go into a “search” mode looking for the signal from its paired Sensor. However, it is …

The.Solar Sync is a sensor system that, when connected to a compatible Hunter controller, will automatically adjust your controller watering run times based upon changes in local climate conditions.The Solar Sync utilizes a solar and temperature sensor to …

The Solar Sync sensor is simple and easy to install and is compatible with all current Hunter AC powered controllers. The sensor should be  placed in an area where it can receive full sun and rain; The  Solar Sync sensor measures solar radiation and …

The Pro-C / PCC controller (with SOLAR SYNC position on dial) is programmed with the Solar Sync technology and, therefore, does not require the use of the Solar Sync module. The Solar Sync Sensor (SOLARSYNCSEN or WSSSEN) is wired directly to the “SEN” …

The I-Core now has the Solar Sync software built into the controller. New I-Core controllers with built in Solar Sync are easily identified by the new Solar Sync Settings dial position on the facepack. Because the new I-Core has built in Solar Sync …