SRC Plus Controller Has Been Replaced By PCC The SRC was Hunter's entry-level residential controller that stopped shipping in 2011. The SRC was replaced by the PCC, a fixed-station, cost effective upgrade developed to offer the homeowner a more efficient …

The XC Controller Has Been Replaced by the X-Core The XC was Hunter's entry-level residential controller that was sunset in 2010. The XC was replaced by the X-Core, which was developed as a more efficient and versatile solution for the same applications. …

EC Controller Has Been Replaced By X-Core The EC was Hunter's entry-level residential controller that stopped shipping in 2006. The EC was replaced by X-Core, which was developed as a more efficient and versatile solution for the same residential …

The ability to remotely command a controller means operators never have to walk back and forth to stop and start irrigation. Winterization is quick and easy and can be accomplished with only one worker. A mid-range solution for residential and commercial …

This feature allows the user to select a time delay between the end of one station run time and the start of another station's run time. The delay can be set for 1 second up to 4 hours. The delay is a convenient feature when working with slow closing …

Non-volatile memory is a feature on all Hunter controllers, back up memory is stored with the assistance of a lithium battery installed inside the controller. This lithium battery is replaceable on these model controllers: I-Core, X-Core, EC, & XC. On all …

A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time. NOTE: In the Start Times dial position, the numbers …

If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down. If you have a master valve on your system (check for …

To stop a station from running when the system cycles automatically, simply remove all station Run Times for station that you do not to operate. Make sure Programs A, B, C and on some controllers Program D, have a run time set to "0:00" for station that …

The project consists of 48438 ft2 (4500 m2) of irrigated area, there are 16146 ft2 (1500 m2) of Green Walls, 5382 ft2 (500 m2) of green roofs and 26910 ft2 (2500 m2) of regular landscape. The green wall irrigation system has 8 zones in the inside system …

This video goes into the advanced features of programming an X-Core controller including setting multiple programs, system off setting, manual operation, seasonal adjustment, and sensor bypass switch. … Hunter X-Core Programming 2 of 2 : Multiple Programs …

Learn to wire your Soil-Clik moisture sensor with Hunter's Pro-C, X-Core, I-Core, and ACC irrigation controllers. Soil-Clik can also be installed on non-Hunter controllers by interrupting the common wire to interrupt the valves when the soil is wet. … …

X-Core Selecting Specific Days of the Week to Water …

If want to clear the memory on your controller and start from fresh or if your controller is not responding to your commands, this video will show you how to reset it. Most Hunter controllers are reset to factory defaults the same way. The SRC and SVC …

One of the most common reasons for a sprinkler system to water intermittently and show the word DELAY on the display is because a delay time was programmed into the controller. This video will show you how to get rid of this delay … Canceling a Delay on a …

This video will teach you how to program your controller to water every other day by selecting odd or even days of the week to water. You will also learn how to set an Interval day schedule that skips 1 to 31 days between watering. … Programming Odd & …

An irrigation system that is repeating the cycle and continuously watering most likely has too many start times programmed into the controller. This video will explain what a start time is and how you can cancel those extra start times that you may not …

Hunter Technical Services shows you how to properly connect and program a Solar Sync sensor to an X-Core controller. … Hunter X-Core Solar Sync Sensor Installation and …

This segment goes over basic programming of the X-Core residential irrigation controller. Setting the current time and day, start times, run times, and days to water will be explained.  Navigation of the controller using the dial and green buttons will …

Hunter controllers allow you to start a station or an entire program manually. To do so, turn the dial to Manual Single Station or Manual All Stations, verify that the stations that you want to activate have run time, and turn the dial back to the Run …

If your display is blank, unreadable, or if it is showing symbols that do not make any sense, this video will teach you how to troubleshoot the display. … Display Troubleshooting on a Hunter …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …