Once you’ve determined that the controller and valve are working properly, you need to take a closer look at the wiring to determine where the problem may lie. In this case you need to first locate track the wire path with your wire & valve locator, then …

We’ll show how to set up a typical wire and valve locator, how to locate a valve, track and mark the wire location to aid in troubleshooting wiring issues, and how to determine the wire depth. Wires are normally buried in the same trench as the mainline, …

Hunter Technical Services shows you how to properly connect and program a Solar Sync sensor to an X-Core controller. … Hunter X-Core Solar Sync Sensor Installation and …

This segment goes over basic programming of the X-Core residential irrigation controller. Setting the current time and day, start times, run times, and days to water will be explained.  Navigation of the controller using the dial and green buttons will …

Hunter controllers allow you to start a station or an entire program manually. To do so, turn the dial to Manual Single Station or Manual All Stations, verify that the stations that you want to activate have run time, and turn the dial back to the Run …

If your display is blank, unreadable, or if it is showing symbols that do not make any sense, this video will teach you how to troubleshoot the display. … Display Troubleshooting on a Hunter …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …

Programming a controller is easy. You just need to program the current day and time and you are ready to create a program for your zones or stations. It only takes three ingredients to complete a program: a start time, run times, and days to water. A …

This video goes into the advanced features of programming an X-Core controller including setting multiple programs, system off setting, manual operation, seasonal adjustment, and sensor bypass switch. … Hunter X-Core Programming 2 of 2 : Multiple Programs …

LCD Display (both Indoor & Outdoor Models) Run Times: Allows the user to set each valve station run time from 1 minute to 4 hours Start Times: Allows 1 to 4 start times to be set in each program Station Number: Indicates currently selected station number …

Before securing the controller to the wall, you must first remove the lower wiring compartment door. The door can easily be removed by following the simple steps below: Open the external door using the included key if outdoor version model. Indoor version …

Installation of the X-Core should only be done by trained personnel. … X-Core - Connecting Valves and Transformer …

The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …

A high-energy lithium battery is included with your X-Core controller. The battery allows the user to remotely program the controller without connecting AC power. It is also used to keep the current time and day during power outage conditions. To replace …

NOTE: Complete this section only if you have a pump start relay installed. A pump start relay is a device that uses a signal from the controller to actuate a separate electrical circuit to energize a pump to provide water to your system. The controller …

A Hunter weather sensor or other micro-switch type weather sensors can be connected to the X-Core. The purpose of this sensor is to stop automatic watering when weather conditions dictate. Compatible Hunter Clik sensors include the   MINI-CLIK ® ,  …

The X-Core Controller is compatible with Hunter Remote Controls (not included). The SmartPort® wiring harness (included with all Hunter Remotes) allows for fast and easy use of the Hunter controls. The Hunter remotes make it possible for you to operate …

The X-Core display shows the time and day when the controller is idle. The display changes when the dial is rotated to indicate the specific programming information to enter. When programming, the flashing portion of the display can be changed by pressing …

NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations. The numbers represent the program start times. Each program can start up to 4 times on the set days to water. One start time will activate all stations sequentially in that …

X-Core - Setting Station Run Times …

X-Core Setting Days To Water …

With this option you can select interval watering from 1 to 31 days. … X-Core selecting Interval Watering …