NPT or National Pipe Thread has become a US standard for tapered threads used on pipe and fittings. The taper rate for all NPT thread is 1/16 th of an inch. When torque is applied to an NPT fitting compression will cause the flanks to create a seal; as …

1.     Turn the dial to the RUN position. 2.     Remove the 9V battery. 3.     Hold down the  3.     Hold down the , and program buttons simultaneously. 4.     While holding down the three buttons, press and release the Reset button on the back of the …

SRC Reset Unplug the controller's transformer and remove the battery. Press and hold down the ,  and  buttons. Plug the controller's transformer back in. Release the ,    and   buttons. The display should now show 12:00a.m. All the memory has been cleared …

The Erase All feature will erase all of the controller's memory and set everything back to factory presets. Once you perform an Erase All , all programming will be erased, including the Easy Retrieve saved programming. Erase All is usually performed when …

It is recommended procedure to first retrieve the program from a WVC, review and make necessary changes, and then transmit the new program back to the WVC. … Entering the WVC Identification Code Each WVC controller has a unique 3-digit identification code …

The ACC controller can be reset, erasing some, or all programmed information. There are 5 different levels of reset command available.  Once any of them is chosen, the information will be permanently erased. Turn the dial to the RUN Position. Press and …

   The Flow-Clik ™   system includes the HFS (Hunter Flow-Sync® ) as well as the Flow-Clik  interface module. This system is designed to be used with controllers that do not have the capability to process flow information built in. The Flow-Clik  will …

Setting the Start time Push  the   button until the Start Watering Times icon is displayed. The display will show the station number, (larger size number to the left of the Start Time icon) start time number (smaller size number to the rig ht of the …

Each WVC controller requires a unique 3-digit identification number for proper radio operation with the WVP. Setting unique addresses for each WVC allows for separate radio programming and manual operations with individual WVC controllers even though …

The chattering you hear on a pump start relay is usually caused by insufficient amperage arriving at the relay from the controller.  The first question you should ask yourself is – Did this Relay work for some time before or is this new installation? New …

The ROAM-XL Remote offers two separate modes with different station counts.  This should be set based on the controller model. Controller Mode X-Core rE (Residential Mode) PRO-C/HPC rE (Residential Mode) ACC-1200/A2C-1200 rE (Residential Mode) …

The ROAM XL is the updated version of the ICR remote control system. … If you have ICR receivers already in place, they can be used with the new Roam XL Transmitter and conversely the ROAM XL receiver can be used with the ICR Transmitters. …   Note: The …

Resetting the controller will erase the current program data and restart the controller. A reset does not, however, delete a program saved to permanent memory using the Easy Retrieve Memory feature to save a preferred program. …   From the Idle Mode …

1. Press and hold down the , and buttons. 2. Press and release the RESET button in the lower wiring compartment. 3. Wait 2 seconds and release the ,  and  buttons. The display should now show 12:00a.m. 4. All the memory has been cleared and the controller …

     The SVC has been an exceptional battery operated controllers for many years. There are a number of advances within the new version Node controller. For starters, the Node utilizes two 9 volt batteries for extended battery life as compared to one …

This chart can help determine the spacing you need for your soil type.   SOIL TYPE SAND LOAM CLAY Emitter Distribution - Illustration of how the water is distributed in different soils. Saturation Rate in/hr .75 - 1.25 .25 - .75 .15 - .25 mm/hr 19 - 32  6 …

Facepack Identification Stops all irrigation; enables and disables Rain Shutdown. Sets run times and order for stations and Blocks. Accesses multiple options and controller settings. Different sets of options appear, depending on mode controller is in …

In order to properly handle your requests for any Hunter products under warranty, we need to know the date of manufacture for the items in question. Below you will find basic information on how to locate and read the date code on a variety of Hunter Golf …

Please select from the following choices to assist you with your Wireless Mini-Clik Sensor. Optional Quick Response® Technology  - Immediate shutoff feature. Bypassing the Sensor  - Turning the sensor off temporarily. Setting the Transmitter Address at …

Production of the G-Type rotor was discontinued 14 years ago, though many are still in use today. If a G-Type rotor needs to be replaced, the PGP-ADJ or PGP-Ultra is the current equivalent replacement.          … Residential Rotors - Equivalent …

There are two reasons why there might be a wet spot around your sprinkler: The most common reason is called "Low Head Drainage." This is when the lowest head on the zone drains residual water from the piping system out of the sprinkler. Eventually, the …

The MP Rotator's coverage distance depends on incoming pressure. You may not have the correct pressure if you are not achieving the desired distance. … If the distance of coverage is short, you may have low pressure. First, check if your valve has a flow …

The CYCLE & SOAK feature allows you to split a station’s runtime into shorter watering periods. The shorter watering periods will help prevent runoff in situations like slopes or tight soils. It is recommended that the CYCLE time is less than the …

Here are some common reasons why a pop-up sprinkler may stay stuck up: Debris in the pop up body The riser is damaged The riser seal is worn   To fix this: Unscrew the body cap Pull out the sprinkler assembly Examine the parts Clean out debris Replace …