ACC Update Instructions You will need the following to complete the update: USB cable, A/B type. This standard USB cable has a flat end (for the computer) and a rounded square end, for the facepack A pen or something pointy to press the Reset button on …

The controller can be placed in direct connect mode, allowing an iOS or Android device to connect directly over Wi-Fi to a single controller. This removes the need to go through the Wi-Fi router or network in order to communicate directly with the …

The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …

NOTE:  Complete this section only if you have a master valve installed in your irrigation system. A master valve is a “normally closed” valve installed at the supply point of the main line that opens only when the controller initiates a watering …

NOTE:  Complete this section only if you have a pump start relay installed. A pump start relay is a device that uses a signal from the controller to actuate a separate electrical circuit to energize a pump to provide water to your system. The controller …

A Hunter CLIK sensor or closed circuit type weather sensors can be connected to the X2. The purpose of this sensor is to stop automatic watering when weather conditions dictate. … X2 - Connecting a CLIK …

The X2 Controller is compatible with Hunter Remote Controls (not included). The SmartPort® wiring harness (included with all Hunter Remotes) allows for fast and easy use of the Hunter controls. The Hunter remotes make it possible for you to operate the …

Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … HEMT - Hunter Emitter Multi-Tool … Dripline …

Emitter tool for punching a pilot hole, inserting, and removing an emitter. … Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … Pocket Punch … HEMT - Hunter Emitter Multi-Tool … Emitter …

Before securing the controller to the wall, you must first remove the lower wiring compartment door. The door can easily be removed by following the simple steps below: Open the external door using the included key if outdoor version model. Indoor version …

The X-Core display shows the time and day when the controller is idle. The display changes when the dial is rotated to indicate the specific programming information to enter. When programming, the flashing portion of the display can be changed by pressing …

NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations. The numbers represent the program start times. Each program can start up to 4 times on the set days to water. One start time will activate all stations sequentially in that …

X-Core - Setting Station Run Times …

X-Core Setting Days To Water …

With this option you can select interval watering from 1 to 31 days. … X-Core selecting Interval Watering …

The X-Core allows you to program a No Water Day(s). This feature is useful to inhibit watering on specific day(s). For example, if you always mow the lawn on Saturdays, you would designate Saturday as a No Water Day so that you are not mowing wet grass.   …

This feature uses numbered day(s) of the month for watering instead of specific days of the week (odd days: 1st, 3rd, 5th, etc.; even days: 2nd, 4th, 6th, etc.). NOTE: The 31st of any month and February 29th are always “off” days if Odd watering is …

Seasonal Adjustment is used to make global run time changes without re-programming the entire controller. To use the Seasonal Adjustment feature: NOTE: The controller should always be initially programmed in the 100% position. … To view the adjusted run …

After programming the X-Core, set the dial to the RUN position to enable automatic execution of all selected watering programs and start times. … X-Core - Automatic …

For drip irrigation systems using BTT, we recommend using regulation and filtration systems on all residential and commercial applications.   Filters shall install directly on BTT's 3/4" hose thread outlet and connect to drip tubing providing regulated …

Use MP Rotator tools and accessories to optimize the uniformity and overall efficiency of irrigation systems. The MP Rotator Gauge, for instance, measures system pressure at the sprinkler to demonstrate the MP Rotator Nozzle's ability to save water.  If …

If your MP Rotator Nozzle is not rotating, there may be debris in the nozzle. Remove the nozzle to inspect and clean the filter screen. Replace the nozzle and turn the valve on to run the sprinklers. Increase the radius to its largest adjustment by …

REL 2 is used to allow multiple controllers to operate the same low-voltage device (Master Valve or Pump Start Relay).  IMPORTANT: REL 2 is NEVER connected to high voltage. It is for 24VAC devices, only. Diagrams listed below: … … … Two Controllers With …

FloGuard Technology supplements the robust, field-proven features and benefits of the Hunter Pro-Spray® family with an additional level of water savings. When the nozzle is removed from the head of a Pro-Spray model with FloGuard, a single 10' tall …