Pro-C - Installing a Wireless Solar Sync

1. Make sure power to the controller is turned off.
2. Remove the metal jumper plate (if installed) from the sensor terminals.
3. Connect the black wire to the "SEN" terminal location (it does not matter which "SEN" terminal is used).
4. Connect the green wire to the other "SEN" terminal location.

The Solar Sync Receiver can be mounted on the side of the Pro-C controller using an available knock out and secured with the supplied conduit nut. Or, use the supplied bracket to mount the Wireless Receiver on the wall next to controller. Depending on the installation, the supplied 1.5" (3.8cm) extender may be required. Route the wires from the Wireless Receiver into the controller cabinet.

Turn the dial to the SOLAR SYNC position. The display will initially show dashed lines and then will show the default Region setting (3) on the left and the default Water Adjustment setting (5) on the right.

Adjust the Region by using the up or down arrows. Press the right arrow once, the Water Adjustment will be flashing. Adjust the Water Adjustment by using the up or down arrows.

Begin by activating the CR2032 backup battery (used for date/time backup in the event of a power outage) by pulling the battery insulator at the bottom of the module. The expected battery life is ten years. If the battery requires replacement, the battery compartment is located on the back of the Solar Sync module. Remove the cover and install the battery with the positive side (+) of the battery visible, facing toward you. Replace the battery cover. Replace battery with CR2032 type battery only. Use of another battery may present a risk of fire or explosion.

The Solar Sync module is designed to be wall-mounted next to the irrigation controller. A rubber cover is provided for outdoor installations to protect the module from the weather. Use two anchors or self-tapping screws to secure the module to the wall. Place the rubber cover mounting tab behind the module before screwing the module to the wall.

MODULE

The PCC series version of the Pro-C is designed so that the Solar Sync module can be installed inside the controller cabinet. Use the two screws provided to mount the module as shown in the diagram.

1. Connect the red wire from the Solar Sync module to the AC1 terminal
2. Connect the white wire from the Solar Sync module to the AC2 terminal
3. Connect the blue wire from the Solar Sync module to the REM terminal
4. Remove the flat metal jumper from the two SEN terminals
5. Connect the yellow wire to one of the SEN terminals
6. Connect the orange wire to the other SEN terminal

WIRELESS RECEIVER

Mount the Wireless Receiver on the controller cabinet using an available knock out and secure with the supplied conduit nut. Or, use the supplied brackets to mount the Wireless Receiver on the wall. Depending on the installation, the supplied 1.5" (3.8 cm) extender may be required (shown below). Route the wires from the Wireless Receiver into the controller cabinet.

1. Make sure power to the controller is turned off
2. Connect the black Receiver wire to the black Module wire
3. Connect the green Receiver wire to the green Module wire
4. Initialize communication by following steps outlined in “Addressing Wireless Receiver/Sensor” section

MODULE

For the PC series Pro-C Modular controller, mount the Solar Sync module on the wall next to the controller cabinet. There is an additional knockout on the right side of the controller cabinet to route Solar Sync wires into and out of the cabinet.

1. Connect the red wire from the Solar Sync module to the AC1 terminal
2. Connect the white wire from the Solar Sync module to the AC2 terminal
3. Connect the blue wire from the Solar Sync module to the REM terminal
4. Remove the flat metal jumper from the two SEN terminals
5. Connect the yellow wire to one of the SEN terminals
6. Connect the orange wire to the other SEN terminal

WIRELESS RECEIVER

Mount the Wireless Receiver on the controller cabinet using the options described for the PCC Series. Due to the position of the power module in the Pro-C controller, a more convenient option may be to mount the Wireless Receiver to the wall using the Wall Mount Bracket.

1. Make sure power to the controller is turned off
2. Connect the black Receiver wire to the black Module wire
3. Connect the green Receiver wire to the green Module wire
4. Initialize communication by following steps outlined in "Addressing Wireless Receiver/Sensor" section

The Wireless Solar Sync Receiver and Sensor are already paired with the same frequency for an easy installation. When installed, the wireless Receiver will automatically go into a “search” mode looking for the signal from its paired Sensor. However, it is a good idea to initialize communication manually between the wireless Receiver and Sensor during installation to verify correct signal transmission.

To initialize communication manually between wireless Receiver and Sensor:

• After Receiver’s green and black wires have been connected (see “Connecting To The Controller” section), restore power to the controller
• The red LED in the center of the wireless Receiver will turn on and stay solid for 10 seconds, indicating that it is in search mode, searching for a signal from a wireless sensor
• While the red LED is solid and the wireless Receiver is in search mode, press and hold the spindle on the wireless Sensor. The LED on the wireless Receiver will blink 4 times and then turn off, indicating that the signal from the wireless Sensor has been acknowledged.

To Validate Receiver/Sensor Communication or Re-address:

• Press and hold the spindle on the wireless Sensor
• The LED on the wireless Receiver will blink 2 times, confirming that the Receiver is addressed to the Sensor properly

The Solar Sync is simple to program. Only a few initial steps are necessary to program the module. When power is initially turned on, the display will show the time of day. Pressing the   button will sequence through the programming functions on the module. An arrow along the bottom of the display will indicate the function being programmed.

Current Time

Press the   button press until the arrow is displayed over the clock icon. The time of day will be flashing. Use the   or   button to set the current time. The arrow to the right of the display indicates AM or PM.

Note: 24 hour mode will only be enabled with a 50 Hz power input.

Controller Type

Press the   button until the arrow is displayed over the controller icon. Use the   or   button to select the correct Hunter controller.

Region

For accurate measurements, the Solar Sync module needs to be programmed for the typical ET (average July ET) for your region. Press the   button until the arrow is displayed over the globe icon. Use the   or   button to select your region (regions 1 through 4).

Watering Adjustment

If you find that your landscape is "wetter" or "drier" than it should be, a watering adjustment function is provided to adjust watering equally to all stations. Use the   button until the arrow is displayed over the water icon icon. Use the   or   button to increase or decrease the amount of watering scaled 1 to 10 (1 for less water and 10 for more water). Hunter recommends observing performance carefully over the first weeks of operation before adjusting the watering.

NOTE: The Solar Sync module offers a “No Water Window” that prevents any irrigation from occurring during a specific period of the day. The “No Water Window” is a hidden feature on the module. Press and hold the right arrow button for 5 seconds to program the "No Water Window."

A right arrow will be flashing at the START along the right side of the display. Use the   or   buttons to adjust the time you would like the no watering period to start. Pressing the   button again will display an arrow flashing at END. Use the   or   buttons to adjust the time you would like the no watering period to end.