Using the PRB, the regulator in the body will take incoming pressures of 55-100 PSI and reduce them down to 45 PSI. This provides the optimum nozzle pressure to deliver the correct size droplets to the landscape for maximum water efficiency. Please …

You can access reports for your controllers by selecting  REPORTS  at the bottom for the mobile version.  Use the settings on the report tab to the right of the screen to change the following: Change the range of the report Clear all report data Refresh a …

Installing and maintaining an irrigation system is a complex task. That's why it's best to hire a qualified professional. Get connected with a local authorized landscape professional. Find A Contractor Hunter is dedicated to connecting our customers with …

Manual operation allows you to run a manual cycle from 0:01 (one minute) to a maximum of 6:00 (six hours).   With the app open, select the MANUAL HAND  icon. Select a RUN TIME . Click START . Click STOP to stop the manual operation. … Manual operation …

A blank nozzle is available as part of the Low-Angle Nozzle Set (PGP-ADJ P/N: 233200 & PGP Ultra/I-20 P/N:356605SP) , which can be inserted into the rotor to shut off the flow of water. The riser will still pop up as if the rotor is going to water so be …

If your Hunter SRC controller’s display reverts back to the current time after trying to manually activate stations, it has more than likely undergone a power surge or is experiencing a technical anomaly. Most likely this controller will need to be …

Regulating pressure saves water and extends the life of the irrigation system. Water savings is achieved by operating each zone at the best pressure for that equipment and application type. Accu-Sync ensures that every zone in every system stays in check …

Hunter prefers the use of Hunter valves with a Hunter DC-latching solenoids (P/N #458200) for best performance, however, existing irrigation systems can be retrofitted with another manufacturer’s valve and solenoid. Hunter has tested and published a …

Hunter's ET System has a wind option that utilizes an anemometer to read local wind conditions. In some cases site conditions may require the anemometer to be located away from the ET Sensor. If this is the case, using 18AWG wire the anemometer can be …

The ICD-HP Handheld Programmer is an innovative setup, programming, and diagnostic tool for Hunter ICD and DUAL series decoder products. The ICD-HP may be flash updated to the latest version, with a free download from the product Resources page. Version …

Yes, if you know the model of the existing manufacturer's sprinkler, you can use our Replacement Charts to find the appropriate Hunter pop-up or rotor that will have a similar flow and distance range. Hunter has rotors and sprinklers to fit all …

The  CUSTOM IMAGE  feature allows the user to add an image from their existing phone library or the option to take a new one. This is a useful tool when you have multiple controllers/stations on-site to identify locations. NOTE:  The app version 5.0.1869 …

To allow P/MV switching of water sources on sensor inputs, each station will need to be enabled for both P/MV outputs. When the sensor is triggered (open or closed), the P/MV that is not in use will be set to "Close P/MV." Depending on the status of the …

Drip zones need regulation because the working pressure of a drip zone is lower than any other type of system. Hunter offers two options for pressure regulation - a 25 psi(1.7 bars/170 kPa) and a 40 psi(2.8 bars/280 kPa) version. The 25 psi version is …

Spray Body - Check Pressure …

The NODE-BT app offers a  COPY/PASTE SCHEDULE  feature that allows users to create specific irrigation schedules (e.g., start times, run times, water days) and quickly import them into additional controllers as needed. Use this helpful tool to save time …

Native plant restoration projects and subsurface drip irrigation systems often require temporary overhead watering to support delicate plants. To simplify temporary irrigation, two preassembled stake kits are available for use with high-efficiency MP …

Irrigation systems utilize a 24VAC electronic signal to initialize a valve's solenoid. Even though the system is low voltage, it is still always recommended a trained professional perform these tests.   … Using the AC voltage reading on your voltmeter, …

The BTT controller retrieves the local date and time from the smartphone it is paired with and updates every time a smartphone device is connected. The date and time for the controller can only be changed via smartphone settings. You can test by setting a …

To stop a station from running when the system cycles automatically, simply remove all station Run Times for station that you do not to operate. Make sure Programs A, B, C and on some controllers Program D, have a run time set to "0:00" for station that …

When using the side strip nozzles, there are several different configurations that can be done with any given design. For this reason, we would recommend using the Total Area Method to calculate your rate.  … The precipitation rate for a “system” is the …

When using a ROAM, ROAM-XL, ICR, or SRR remote, you may come across a controller that gives you an ERR or SP ERR message. There are two reasons that would cause one of these messages. Miswired Smartport Wrong Station Count on Transmitter … CAUSE  -  Noise …

Your ROAM Transmitter comes from the factory with the maximum station number set to 15. This means that when you use the UP and DOWN buttons to change the station, you may change it to any number between 1 and 240. However, if you only have a 6-station …

Under the Water Days or Days to Water dial position on your controller you have three options. You can have the program run on specific days, an odd/even schedule, or an interval schedule. To move out of the Interval mode and back into one of your other …