The CYCLE & SOAK feature allows you to split a station’s runtime into shorter watering periods. The shorter watering periods will help prevent runoff in situations like slopes or tight soils. It is recommended that the CYCLE time is less than the …

Here are some common reasons why a pop-up sprinkler may stay stuck up: Debris in the pop up body The riser is damaged The riser seal is worn   To fix this: Unscrew the body cap Pull out the sprinkler assembly Examine the parts Clean out debris Replace …

There are two reasons why there might be a wet spot around your sprinkler: The most common reason is called "Low Head Drainage." This is when the lowest head on the zone drains residual water from the piping system out of the sprinkler. Eventually, the …

The MP Rotator's coverage distance depends on incoming pressure. You may not have the correct pressure if you are not achieving the desired distance. … If the distance of coverage is short, you may have low pressure. First, check if your valve has a flow …

This chart can help determine the spacing you need for your soil type.   SOIL TYPE SAND LOAM CLAY Emitter Distribution - Illustration of how the water is distributed in different soils. Saturation Rate in/hr .75 - 1.25 .25 - .75 .15 - .25 mm/hr 19 - 32  6 …

Irrigation systems utilize a 24VAC electronic signal to initialize a valve's solenoid. Even though the system is low voltage, it is still always recommended a trained professional perform these tests.   … Using the AC voltage reading on your voltmeter, …

The BTT controller retrieves the local date and time from the smartphone it is paired with and updates every time a smartphone device is connected. The date and time for the controller can only be changed via smartphone settings. You can test by setting a …

To stop a station from running when the system cycles automatically, simply remove all station Run Times for station that you do not to operate. Make sure Programs A, B, C and on some controllers Program D, have a run time set to "0:00" for station that …

When using the side strip nozzles, there are several different configurations that can be done with any given design. For this reason, we would recommend using the Total Area Method to calculate your rate.  … The precipitation rate for a “system” is the …

Operation Check to Verify Correct Wiring Turn on one zone of the irrigation system that is visible while you are in reach of the Mini-Clik. Manually depress the spindle at the top of the Mini-Clik until you hear the switch “click” off. The sprinkler zone …

Setting the Start time Push  the   button until the Start Watering Times icon is displayed. The display will show the station number, (larger size number to the left of the Start Time icon) start time number (smaller size number to the rig ht of the …

Each WVC controller requires a unique 3-digit identification number for proper radio operation with the WVP. Setting unique addresses for each WVC allows for separate radio programming and manual operations with individual WVC controllers even though …

The chattering you hear on a pump start relay is usually caused by insufficient amperage arriving at the relay from the controller.  The first question you should ask yourself is – Did this Relay work for some time before or is this new installation? New …

The ROAM-XL Remote offers two separate modes with different station counts.  This should be set based on the controller model. Controller Mode X-Core rE (Residential Mode) PRO-C/HPC rE (Residential Mode) ACC-1200/A2C-1200 rE (Residential Mode) …

The ROAM XL is the updated version of the ICR remote control system. … If you have ICR receivers already in place, they can be used with the new Roam XL Transmitter and conversely the ROAM XL receiver can be used with the ICR Transmitters. …   Note: The …

The firmware in the older SRC controllers does not go past 2011. The controller can be utilized well in 2011 by following some simple steps. You can choose the year that correlates with the current calendar year from Sunday through Monday. Select the …

Resetting the controller will erase the current program data and restart the controller. A reset does not, however, delete a program saved to permanent memory using the Easy Retrieve Memory feature to save a preferred program. …   From the Idle Mode …

1. Press and hold down the , and buttons. 2. Press and release the RESET button in the lower wiring compartment. 3. Wait 2 seconds and release the ,  and  buttons. The display should now show 12:00a.m. 4. All the memory has been cleared and the controller …

     The SVC has been an exceptional battery operated controllers for many years. There are a number of advances within the new version Node controller. For starters, the Node utilizes two 9 volt batteries for extended battery life as compared to one …

NPT or National Pipe Thread has become a US standard for tapered threads used on pipe and fittings. The taper rate for all NPT thread is 1/16 th of an inch. When torque is applied to an NPT fitting compression will cause the flanks to create a seal; as …

Facepack Identification Stops all irrigation; enables and disables Rain Shutdown. Sets run times and order for stations and Blocks. Accesses multiple options and controller settings. Different sets of options appear, depending on mode controller is in …

In order to properly handle your requests for any Hunter products under warranty, we need to know the date of manufacture for the items in question. Below you will find basic information on how to locate and read the date code on a variety of Hunter Golf …

1.     Turn the dial to the RUN position. 2.     Remove the 9V battery. 3.     Hold down the  3.     Hold down the , and program buttons simultaneously. 4.     While holding down the three buttons, press and release the Reset button on the back of the …

SRC Reset Unplug the controller's transformer and remove the battery. Press and hold down the ,  and  buttons. Plug the controller's transformer back in. Release the ,    and   buttons. The display should now show 12:00a.m. All the memory has been cleared …